Author Topic: Power feed mod for the lathe  (Read 648 times)

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Power feed mod for the lathe
« on: April 09, 2017, 10:37:33 PM »
A project I have been meaning to do. Add a variable speed to my lathe. This will make it possible to adjust feed rate without stopping to change gears and being able to fine tune your feed to what you re turning.


<a href="http://www.youtube.com/watch?v=8NI1GgMIP-o" target="_blank">http://www.youtube.com/watch?v=8NI1GgMIP-o</a>
George

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2111
  • Country: gb
Re: Power feed mod for the lathe
« Reply #1 on: April 10, 2017, 03:08:26 AM »
Doc,
Looking good so far... :thumbup:

Good idea repurposing a box rather than throwing away....
Look forward to seeing some more... :dremel:
eccentric millionaire financed by 'er indoors
Location:  near Hull

Skype: chippiejnr

Offline raynerd

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2847
  • Country: gb
    • Raynerds Projects - Raynerd.co.uk
Re: Power feed mod for the lathe
« Reply #2 on: April 10, 2017, 03:53:34 AM »
Nice work - like that!
Youtube: craynerd
Projects at - www.raynerd.co.uk

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #3 on: April 10, 2017, 10:23:06 PM »
Thanks guys!

Continued lathe power feed mod.

<a href="http://www.youtube.com/watch?v=xwrsW2Wp9sI" target="_blank">http://www.youtube.com/watch?v=xwrsW2Wp9sI</a>
George

Offline krv3000

  • Hero Member
  • *****
  • Posts: 1899
  • Country: gb
Re: Power feed mod for the lathe
« Reply #4 on: April 11, 2017, 06:00:10 PM »
brill

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #5 on: April 11, 2017, 10:26:40 PM »
Thanks Krv3000



Continuation of lathe power feed mod.




<a href="http://www.youtube.com/watch?v=voIqYqyP1JI" target="_blank">http://www.youtube.com/watch?v=voIqYqyP1JI</a>
George

Offline DaveS

  • Jr. Member
  • **
  • Posts: 21
  • Country: gb
Re: Power feed mod for the lathe
« Reply #6 on: April 12, 2017, 06:23:26 AM »
I am not seeing any photos or videos on this thread but previous replies have indicated they are visible?


Dave

Offline PekkaNF

  • Hero Member
  • *****
  • Posts: 1599
  • Country: fi
Re: Power feed mod for the lathe
« Reply #7 on: April 12, 2017, 07:27:46 AM »
My FireFox does not show them either, but they are in YouTube. Something to do with old Flashsomethingbuggy.

it does not show embeded, but link should work, starting from here:
https://youtu.be/8NI1GgMIP-o

Pekka

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 5064
  • Country: gb
  • East Sussex, UK
Re: Power feed mod for the lathe
« Reply #8 on: April 12, 2017, 01:21:36 PM »
OK they are showing for me under Win7 / Google Chrome, and also showing on an iPad running Safari.

But they are NOT showing for me under Internet Explorer 11 under Win 7 - strange  :scratch:

What operating system and browser are you using Dave ?
Andrew Mawson
East Sussex

Offline shipto

  • Hero Member
  • *****
  • Posts: 592
  • Country: gb
  • Redditch, UK
Re: Power feed mod for the lathe
« Reply #9 on: April 12, 2017, 03:22:44 PM »
Doc sorry if you address it in your video's as once again I have been watching them with sound off due to her indoors watching masterchef but did you think of a center off switch on your direction switch?
Turns out this life c**p is just one big distraction from death but a good one. For the love of god dont give yourself time to think.
https://myshedblog.wordpress.com/

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #10 on: April 12, 2017, 03:41:11 PM »
Yes but doing this on the really cheap Hahaha used what I had.
George

Offline DaveS

  • Jr. Member
  • **
  • Posts: 21
  • Country: gb
Re: Power feed mod for the lathe
« Reply #11 on: April 12, 2017, 04:22:48 PM »
I'm using Firefox as is PekkaNF, I'll try another browser

Dave

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #12 on: April 12, 2017, 04:58:22 PM »
I'm using Firefox (only browser I use) and they show up fine.
George

Offline shipto

  • Hero Member
  • *****
  • Posts: 592
  • Country: gb
  • Redditch, UK
Re: Power feed mod for the lathe
« Reply #13 on: April 12, 2017, 05:03:02 PM »
firefox on windows 10 all fine for me.
Turns out this life c**p is just one big distraction from death but a good one. For the love of god dont give yourself time to think.
https://myshedblog.wordpress.com/

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #14 on: April 12, 2017, 09:33:48 PM »
Continuation of lathe power feed mod.



<a href="http://www.youtube.com/watch?v=mJfP8PA1mFU" target="_blank">http://www.youtube.com/watch?v=mJfP8PA1mFU</a>
George

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #15 on: April 13, 2017, 09:09:51 PM »
Continuation of lathe power feed mod.




<a href="http://www.youtube.com/watch?v=_9f1Qo3NNUE" target="_blank">http://www.youtube.com/watch?v=_9f1Qo3NNUE</a>
George

Offline Doc

  • Sr. Member
  • ****
  • Posts: 397
  • Country: us
  • Old but still usefull (I hope) ?
Re: Power feed mod for the lathe
« Reply #16 on: April 15, 2017, 09:10:53 AM »
  Ok here is another vid on  my lathe power feed mod.  There will be a (I hope) short pause in the mod. I had promised to do a mod to a trailer for my sister-in-law for her motorcycle. I need to lengthen it and add a wheel chock (plan on building one for her like this one Wheel chock. Anyway it will be a bit before I get back t the lathe power feed.



<a href="http://www.youtube.com/watch?v=5qj7T8x59Zg" target="_blank">http://www.youtube.com/watch?v=5qj7T8x59Zg</a>
George