Author Topic: Making a Sub Spindle  (Read 51716 times)

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Making a Sub Spindle
« on: September 14, 2009, 12:49:19 PM »
Hi Chaps

Quite a few of you chaps have posted pics of sub-spindles is use either cross drilling, milling or Rose turning, they can be a very useful addition to a shop and have many applications.

I want to build a spindle that I will eventually use as a tool post grinder, as is my way I did a fair bit of investigation work into them, I've seen tool post grinders used when I was tool making and I've also seen John's in use, so I had a fair idea what they look like. I also bought a book from the Workshop Practice Series (No 27 Spindles by Harpit Sandhu ISBN-13:978-1-85486-149-8) and found it very interesting and informative, it covers the design and manufacture of various spindles for different application from milling, drilling, grinding and even a high speed spindle to take dremel tooling.

I will be following the design for a "Light weight tool post grinding spindle" modified for my own use.

This is a sanitized sketch of the spindle.



I've collected most of the bits needed together.



The bearing came from Arc Euro Trade £2 each, Johns started the ball rolling by putting a 20mm hole down the middle of the bar, this was a job that would have made my little lathe grunt (thanks John  :thumbup:) this will eventually become the spindle housing. The housing will be bored to fit the bearings, so I'll need the bore clock, and has I'm going to hold the bearing in place with screwed caps I'll need to do internal and external screw cutting, I could have used adhesive to fix the bearing, but where's the challenge in that, so  I bought some HSS threading tools from Chronos ( just four days delivery including weekend  :thumbup:), I've still to make a undercut boring bar holder, and I'm waiting for the electric motor that I bought on flebay to be delivered.

So I'm more or less ready to make a start in the next day or two.

Cheers

Stew



A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline Majorstrain

  • Jr. Member
  • **
  • Posts: 24
  • Perth, West Australia
Re: Making a Sub Spindle
« Reply #1 on: September 15, 2009, 12:08:20 PM »
Hi Stew, :wave:

You've got me interested,

It's one tool that I want to make as well.
What were the specs on the motor you ordered on flea bay?
Iv'e been thinking about a brushless DC and controller as used in electric RC aircraft  :zap:

Looking forward to seeing the progress reports.
Cheers
Phil

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #2 on: September 15, 2009, 01:49:08 PM »
Hi Phil

Its a sewing machine motor 1/8 hp 6000 rpm you don't need a lot of power for grinding you're only taking a lick off.

I'm planing on having two sets of pulley one set giving 4000 rpm for external grinding and one set giving 16000 rpm for internal, thats what I'm aiming for anyway.

Its not arrived yet bought it over a week ago sent vendor a PM today asking where it is, hope its not a scam.

Cheers

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline John Hill

  • The Artful Bodger
  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2016
  • Country: nz
Re: Making a Sub Spindle
« Reply #3 on: September 15, 2009, 02:17:34 PM »
Stew,   this is very interesting!

I have started on a spindle too and I am interested in your comments re the motor size as I have started to build mine around a router motor, not a big router but a lot bigger than a sewing machine motor! 

I thought that by using the bigger motor and stepped pulleys I could use it as a drill too (for example drilling holes around a diameter in a flywheel or suchlike).

From the den of The Artful Bodger

bogstandard

  • Guest
Re: Making a Sub Spindle
« Reply #4 on: September 15, 2009, 02:24:31 PM »
To all,

Even though you are normally only taking minute cuts, you do need the grunt there. If you are grinding a fairly large OD, say 3", that is over 9" circumference, it is the constant drag of the wheel that causes the problems. When I grind on my surface grinder say a piece 4" long at 0.0005" (0.01mm) cut, the 1/2 horse motor starts to slow down. So you have a choice, either more grunt to cut thru it, or super fine feeds so there is not as much grinding pressure.

The way to get your very fine feeds is not to use the crosslide for the feed, but the topslide which has been set over a couple of degrees, and the wheel set and dressed square to the job. Grinding angles then becomes a nightmare to set up.

With reference to motors, the original one used on mine (now replaced) was a 1/6th HP free running at 16K.

Bogs
« Last Edit: September 15, 2009, 02:26:11 PM by bogstandard »

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #5 on: September 15, 2009, 04:13:26 PM »
Thanks for that John

I was looking for a slightly bigger motor but all I can seem to find is 1/3 HP ish with around 1800 rpm the sewing machine motor is the best I could find, but I'll keep looking, if I find something better, the sewing machine motor will be useful for something, I may even take up sewing.

Cheers

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline Maninshed

  • Jr. Member
  • **
  • Posts: 16
Re: Making a Sub Spindle
« Reply #6 on: September 15, 2009, 04:32:49 PM »
If you are using your spindle as a tool post grinder, a thing to be careful with is the bearing preload, I assume you will be using angular contact bearings, as these are better for this type of work they take the axial and end loads better. I built the quorn cutter grinder type spindle, looks very similar to your sketch, but it has a bearing preload system using springs giving about 10lb preload on the bearings. I would think  the book you have will make some referance to preloading bearings.

Martyn

Offline arnoldb

  • Hero Member
  • *****
  • Posts: 515
  • Country: na
  • Windhoek, Namibia
Re: Making a Sub Spindle
« Reply #7 on: September 15, 2009, 04:40:42 PM »
Stew, very interesting.  I'll be closely following this one  :borg:

Cheers, Arnold

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #8 on: September 16, 2009, 03:07:59 AM »
Martyn

I'm going to use ball bearings. Like you I thought taper bearings would be better, from the book the author discuses the use of the Quorn spindle that he thinks is excellent: however, it is best in one direction due to the pre load which is fine for the Quorn, but his spindle could be used in either direction, the author does admit that his solution is not ideal but its simple design makes it easy to manufacture and will allow the bearings to be replaced if undue wear accures.

In his design of what he calls his basic spindle that can be used for milling he uses three bearing a plane bearing at the back and at the front he uses a pair of radial and axial load bearings back to back to take the loads. (I think these are similar to wheel bearing in a car but i'll stand to be corrected on this)

I have looked at the Quorn with a view to making one how have you found it ?, would it be possible to post a few pics so the chaps have an idea what they look like. 

Cheers
 :beer:
Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline NickG

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1890
Re: Making a Sub Spindle
« Reply #9 on: September 16, 2009, 08:08:11 AM »
Stew,

I would have thought taper roller bearings would be ok to deal with axial and radial load. But maybe ball or roller bearings along with thrust bearings would be better still.

I thought car wheel bearings were taper roller ... not sure ... I know mine need doing though!

Nick
Location: County Durham (North East England)

Offline Maninshed

  • Jr. Member
  • **
  • Posts: 16
Re: Making a Sub Spindle
« Reply #10 on: September 16, 2009, 08:42:47 AM »
Hi Stew.
Angular contact bearings are not taper roller bearings, they look similar to a ball type standard bearings. A standard deep groove bearing if you try to push the inner race laterally out of the outer race (finger pressure) in either direction you cannot. However with an angular contact bearing if you do the same there is some detectable lateral play between the inner and outer races, the idea of the preload is to take this out. The races on an angular contact bearing (sometimes there called magneto bearings) are not a compete 'C' shape there are like half a 'C' in opposing directions, therefore the loading angles are different so they can take tangental loads better. I think the type of bearing you use is more critical if you are going to make a high speed spindle for grinding eg tangetal loads as on the perifery of a wheel, or a milling cutter, if the spindle was for lateral loads only eg drilling I guess you could use a standad deep groove bearing. I hope you can understand my drivel, I just copied the quorn spindle out of the Quorn book. I only lurk on this site at the moment, so have not figured out how to do the photos & attachments yet.

Offline Maninshed

  • Jr. Member
  • **
  • Posts: 16
Re: Making a Sub Spindle
« Reply #11 on: September 16, 2009, 08:53:02 AM »
NickG.
Its down to the RPM rating on the bearing, taper roller bearings can go up to about 9,000rpm a standard deep groove bearing can get up to 80,000rpm and the angular contacts can be up to 28,000rpm obviously these max speeds depend on size. Another problem when designing a high speed head is making it compact the footprint of a taper roller is quite big compared to a standard or angular contact bearing.

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: Making a Sub Spindle
« Reply #12 on: September 16, 2009, 08:53:45 AM »
Cars wheel hubs mostly use taper rollers (I think we can agree they can quite take some side and axle loads), my mini lathe now has tapers and my Smart and Brown has a pair of ball races at the front, great big ones that i hope I'll never have to replace and a taper at the back.

The best bit about tapers is you can fine tune the pre-load. But you can over do it as well and ruin the bearing quite quickly.

My pillar drill has one thrust and one roller at the nose and two rollers at the other end.

You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

bogstandard

  • Guest
Re: Making a Sub Spindle
« Reply #13 on: September 16, 2009, 09:16:22 AM »
You might find that car wheel bearings on trialing arm vehicles have gone away from the tapered type to just plain ball bearings.

At one time you could tweak them up and regrease them as well, they would most probably last the life of the car. My car is now 7 years old, and it is now showing signs it needs the rear bearings doing again, last replaced 3 years ago.

Do you honestly think car manufacturers nowadays will make something you can easily change or fix yourself. I could do it and most probably you people could as well, but the average man in the street who would normally have tweaked them up himself, is now forced to pay a couple of hundred squid to get them replaced at their dealership.

With regards to Stews bearing dilemma. I have made a few spindles in my time, and personally, I think the standard bearings he has are plenty good enough for what will be a little used grinding spindle, as long as care is taken in getting the spacer the correct length so that the bearings are not stressed, but running perfectly central when the shaft is tightened up. Pre loading shouldn't be required for what he is doing.

For a more dedicated type of a machine like the Quorn, then yes, make a proper preloaded spindle.


Bogs

Offline Raggle

  • In Memoriam
  • Jr. Member
  • *****
  • Posts: 93
  • Newtown, Powys, Mid-Wales
Re: Making a Sub Spindle
« Reply #14 on: September 16, 2009, 10:42:02 AM »
It's worth remembering that the Unimat SL headstock uses E-13 magneto bearings. Preload is set by the length of the spacer tube between them and a pair of belville washers.

Plenty of SLs have been doing good service for 40-50 years with widely varying loads and I doubt many owners have replaced these inexpensive bearings more than once, if at all. Offhand I'd say they were good for speeds in excess of 6,000 rpm. The Unimat cartridge is 35mm diam which is not over large considering it has a rack and a keyway. Not too difficult to duplicate.

There'll be a drawing of it somewhere on the Yahoo site

http://finance.groups.yahoo.com/group/UNIMAT/

Arc Euro carry E-10s at £6.50 each and angular contact from £6 a pair

http://www.arceurotrade.co.uk/Catalogue/Bearings/Angular-Contact-Ball-Bearings

HTH

Ray
still turning handles  -  usually the wrong way

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #15 on: September 16, 2009, 01:24:41 PM »
Thanks for the input and discussion on bearing selection chaps, very informative, its certainly helped me understand the issues, and help me understand the intricacies of the design. I now understand why the author stressed the importance of getting the spacer spot on between the bearings, I'll have a ponder which way to go but I may go with the plain ball bearings, I've had a look at the arc bearing and I think they have angular contact bearing that are the same size as the the ball bearing I bought, so I'll have the option to change at a later date but I will check this out.

Thanks again

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline John Hill

  • The Artful Bodger
  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2016
  • Country: nz
Re: Making a Sub Spindle
« Reply #16 on: September 16, 2009, 04:27:55 PM »
Some cars have a crushable spacer between the bearings.  I think Lotus ("Lots of trouble usually serious") use(d) they system in the rear hubs of some models.
From the den of The Artful Bodger

Offline NickG

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1890
Re: Making a Sub Spindle
« Reply #17 on: September 17, 2009, 05:57:44 AM »
 Slightly :offtopic: Bogs, you're right there, they don't make easy for us, just for themselves. I still tend to do a lot of work on my cars as I refuse to pay stealer prices! Having said that, I priced up the bearings on my Mini Cooper S and cannotget the bearing separately, it comes as part of the hub with the abs ring, hence £80 each!!! So I'll have to weigh up whether it's worth paying someone the labour on top of that or spending a day doing them ... these things usually need a day allowing because something usually doesn't go to plan! The one thing that makes it worthwhile is the sense of achievement you get when you do anything yourself.

Stew, can't wait to see this project, i've often wanted a spindle on the tool post, you might be able to use a change wheel to index, like when I drilled my holes in cylinder covers etc. If I had some proper indexing method that would have been very good as it's similar to being able to swap chucks to rotary tables like John does.

Nick
Location: County Durham (North East England)

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: Making a Sub Spindle
« Reply #18 on: September 17, 2009, 08:38:59 AM »
Hurry up Stew.....I want to build one too......... :lol:
You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #19 on: September 17, 2009, 11:54:23 AM »
Blimey

Talk about slave drivers,  :poke: :poke: :poke: :poke:

I know a man who'll make you a whip  :lol:

Anyway got on with the housing, this is made from a 38mm (1.5") dia * 150 mm (6") chunk of steel not quite sure what sort I was using but it was a bit tougher than mild steel, first job was to put 20mm hole right down the middle. John kindly did this for me on his more powerful lathe. Then setting it up in a four jaw, clocked it up, and skimmed the OD up for 120mm length. then cut the pocket for the bearing.

This is how the pocket should be sized



Boring the pocket



The bearing is to be a nice slide fit with no woble.

To cut the threads I cheated a bit, as its quite a fine thread and not very long I set the lathe gear train up for 24 TPI set the threading tool up square and cut the thread by winding the lathe over by hand, as my machine doesn't have a threading dial I kept the feed engaged and just wound the chuck backward a forward and nibbled the thread out.



With the first pocket I made the thread length as per the book (3 mm) but this barely gave 2 1/2 full threads, as I don't like things that look as though they well blow over with the fist puff of wind, I went to the brick **** house school of engineering: decided with the second pocket to make the thread length (5 mm), if I'm still not happy with the first one when I make the end caps I'll set it back up and cut it back a and re cut the pocket for a longer thread.

Setting up for the second pocket, the housing was carefully clocked up, take your time with this and get it right, clock it up next to the chuck and at the end other wise the bearing will be skewed .





Now for a confession I didn't use the bore clock, I had a practice and found it just to awkward to use so what I did was turn up a couple of plug gauges one 0.5 mm under size and the other 0.1 mm under size and work to these.

This is the finished housing with the plug gauge



And as you have to get the depth of the bearing seat spot on this is how I measured it.



Plan ahead my boy plan ahead  :lol: :lol: :lol: :lol: :lol: :lol:

Have fun

Stew


 
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline dsquire

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2275
  • Country: ca
  • Kitchener, Ontario, Canada
Re: Making a Sub Spindle
« Reply #20 on: September 17, 2009, 12:07:29 PM »
sbwhart

Now we know why you built the depth gauge. Very clever. :ddb: :ddb: :ddb:

Cheers :beer: :beer:

Don

Good, better, best.
Never let it rest,
'til your good is better,
and your better best

bogstandard

  • Guest
Re: Making a Sub Spindle
« Reply #21 on: September 17, 2009, 12:15:35 PM »
Stew,

I'm going to have to stop you looking around my shop.

You are knocking up these bits of tooling (depth gauge) after seeing my commercial purchases, it just has to stop :lol:


John

Offline NickG

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1890
Re: Making a Sub Spindle
« Reply #22 on: September 17, 2009, 01:35:00 PM »
Excellent Stew!
Location: County Durham (North East England)

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: Making a Sub Spindle
« Reply #23 on: September 17, 2009, 02:06:21 PM »
Thanks Stew, watching this one with great interest.....looking good so far.... :clap:
You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

Offline Gerhard Olivier

  • Sr. Member
  • ****
  • Posts: 314
Re: Making a Sub Spindle
« Reply #24 on: September 17, 2009, 03:02:00 PM »
Nice Stew -  keep it coming :bow:

Gerhard
Guernsey
Channel Islands

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #25 on: September 19, 2009, 10:43:46 AM »
Made the end caps, but not without some difficulty. Up to now I had done very little thread cutting on my machine, so I was going through a bit of a learning curve how to deal with the back lash etc, so I struggled a bit with the first one, but the second was more straight forward.



This is the set up:- what I had to do was take the saddle past the start point, then wind it back by hand to the start point, to help getting the start point I marked the chuck and set the dial bezel on zero. I had to remember to set the correct motor direction before switching on the power, it all seemed to work ok.  :thumbup:

Finished end caps




Cheers
 :beer:
Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #26 on: September 19, 2009, 11:43:22 AM »
Forgot to explain about the threads.  :doh:

Because the size of the threads are dictated by the size of the bearings what you end up with is an illegitimate thread (bastard thread to use the correct technical term). As the internal thread is made first to get to the OD of the male thread for a 60 deg metric thread form you add 2 * 0.036 " to the ID of the internal thread. 0.036 = 1/24TPI * Cos(30)

Cheers
 :beer:
Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline dsquire

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2275
  • Country: ca
  • Kitchener, Ontario, Canada
Re: Making a Sub Spindle
« Reply #27 on: September 19, 2009, 01:15:29 PM »
Forgot to explain about the threads.  :doh:

Because the size of the threads are dictated by the size of the bearings what you end up with is an illegitimate thread (bastard thread to use the correct technical term). As the internal thread is made first to get to the OD of the male thread for a 60 deg metric thread form you add 2 * 0.036 " to the ID of the internal thread. 0.036 = 1/24TPI * Cos(30)

Cheers
 :beer:
Stew

Stew

Do you realize that in maybe 100 years when some future member or MadModder or other forum member comes across this piece of equipment and has to make a new part what this will do to him? :lol: :lol: :lol:

He will say to himself, I'll just go to my scrap bin and get a piece of metal and turn up a new piece and single point a thread and it will be just like when that great machinest made it a 100 years ago. :doh: :doh:

Now as he sits down with his calipers and other measuring tools to make a crap-o-cad drawing everything proceeds fine, until he measures the thread. He looks it up in his metric thread charts and can't find it. Ok, I'll just look in this old Machinest hand book from my Great Great Grandfather, probably be something in there. Nope, lots of threads of all diferent kinds that come close but nothing the same. Ok, I'll post this on the New MadModder forum. Someone there will surley know something about it. :mmr:

.
.
.
.
.
.
As the sun slowly sets in the west he can be seen sitting outside under a man made shade tree slowly pulling out the last of the grey hairs that he has left.  :(

Cheers  :beer:

Don

Good, better, best.
Never let it rest,
'til your good is better,
and your better best

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #28 on: September 19, 2009, 01:28:52 PM »
Don

We could start a new thread standard we could call it Universal MadModder (UMM) with a 60 deg or 55 deg thread form any pitch you want and any Major Diameter you want and any fit you want 

 :mmr:

:lol:  :lol: :lol: :lol: :lol: :lol:

Cheers

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline arnoldb

  • Hero Member
  • *****
  • Posts: 515
  • Country: na
  • Windhoek, Namibia
Re: Making a Sub Spindle
« Reply #29 on: September 20, 2009, 04:15:23 AM »
Great going Stew  :clap: :clap: :clap:

I like your idea of UMM  :lol:  :lol: - could make life interesting for copy-cats  :lol: :lol: :lol:

 :beer: Arnold

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #30 on: September 20, 2009, 05:09:31 AM »
Great going Stew  :clap: :clap: :clap:

I like your idea of UMM  :lol:  :lol: - could make life interesting for copy-cats  :lol: :lol: :lol:

 :beer: Arnold

They'd certainly be doing a lot of UMM-ing  :scratch:

 :lol: :lol: :lol: :lol:

Stew
 
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #31 on: September 21, 2009, 11:11:08 AM »
OK Chaps now for the spindle this bits is quite long 18 cm or 7 " in old money, Most of my bar ends are shorter than this but then I remember I had 3 ' of 32mm dia free cutting tucked away behind the lathe.

First job was to hack saw off a good 7" length, then as I was going to turn it up between centres I needed to put a good deep centre drill in each end for this the bar was sticking out an uncomfortable long way. Took it steady not to fast a speed,  :thumbup: but didn't try facing it off that would have been desaster, I'll just have to live with the cut face.



Working between centres for long jobs as a number of advantages not least you can take the job from between the centres turn it round and everything will still be concentric.

To set up for turning between centres you need a fixed centre in your head stock and a driving dog,



you can use your chuck simply turn a centre on a bit of steel and use the chuck jaws as the driving dog

And you need a carrier on your work this is my collection, picked up from scrappies



First cut



After the first cut mic the work up and check for taper if you've got a taper you can adjust this out by moving your tail stop over:- if is low the tail stop needs moving away from you if its big move it towards you.

The tail stock has two adjusting screws one each side, you simply unlock slacken of the clamp bolts (not the one that clamps it to the slide) and adjust the screws together screw one in screw the other out this slews it over, I do mine with two screw drivers, some have bolts.



These are the clamp bolts on my lathe with a graduation so you can keep track of how much you move it, I put an additional two marks on mine showed where it cuts parallel, for easy setting.



Once I got it parallel I got it to 0.1 over 15 cm length which is good, I turned the large diameter to size, swapped the carrier around so that I could machine the other end then roughed everything out to withing 0.5 mm.





Then as one of the bearings need to slide over the middle section I turned this under size, then very carefully turned the bearing location to a nice shake free fit on the bearing.



And this is it in the bearing housing everything lined up exactly.



Then back in the lathe and screw cut the thread for M12



This is the nearly finished spindle at this point I called it a day Gasping for a cuppa.



Next job cut the key way.

Have fun

Stew





 



A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline NickG

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1890
Re: Making a Sub Spindle
« Reply #32 on: September 21, 2009, 11:39:29 AM »
Looking good stew  :bow:, I know the theory but have never tried turning between centres before. I don't have a catch plate although I guess I could either use the chuck as you said as I have plenty of length between centres, or unbolt the chuck and do what you have done. I don't really like disturbing that although it will go back in in the same place, It's just I made the register quite a tight fit though. Not sure if I have any carriers any more either.

So do you have anything in particular you're going to be using this spindle for?

Nick
Location: County Durham (North East England)

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #33 on: September 21, 2009, 11:47:27 AM »

So do you have anything in particular you're going to be using this spindle for?

Nick

I'm going to use it for a tool post grinder and if all goes to plan a home brewed cutter grinder and if that works I want to use it to make a gear cutting fly cutter and if that works a clock

I think it all started when I swallowed  a fly  :lol:

Tools make tools that make more tools that make things

Cheers

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: Making a Sub Spindle
« Reply #34 on: September 21, 2009, 12:07:25 PM »
Very nice Stew, I want to go out and switch my lathe on now....... :clap:
You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: Making a Sub Spindle
« Reply #35 on: September 21, 2009, 12:12:48 PM »
Stew, when you get a moment can you show us you digi on the lathe. Did it have to be upside down?
You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #36 on: September 21, 2009, 12:18:48 PM »
Hi Darren

This is it



Looking at it I suppose I could have had it further away, I was a bit concerned about protecting it from swarf etc. I'm not going to have it in place all the time, just when I need it when screw cutting.

Cheers

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline Bernd

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3688
  • Country: us
  • 1915 C Cab
    • Kingstone Model Works
Re: Making a Sub Spindle
« Reply #37 on: September 21, 2009, 01:42:54 PM »
Hey Stew,

I've just got to ask. When you got closer to the driving dog with the coolant, did you get your face sprayed?  :lol:

Bernd

P.S. Nice thread by the way.
Route of the Black Diamonds

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #38 on: September 21, 2009, 02:08:54 PM »
Hey Stew,

I've just got to ask. When you got closer to the driving dog with the coolant, did you get your face sprayed?  :lol:

Bernd

P.S. Nice thread by the way.

Yes   :doh:

Stew

A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #39 on: September 22, 2009, 11:32:51 AM »
Ok on the home run now Chaps

Next job cut the key way

Mark where its to go



Find centre of bar and with a 3mm slot drill mill the key way



And mill up and fit brass key



Thats the shaft done next job the spacers that go between the bearings.  There's two spacer 30mm ish long each

Simple turning and drilling job both spacer turned up first before adjusting length



You have to adjust the length of the spacers so that the length of the two together equals the distance between the bearing plus a little bit to tighten down onto.

So put one bearing and spacer into the housing and carefully measure the depth to the spacer, then measure the depth  to the bottom of the bearing pocket take one from the other and that the length to make the other spacer put the spacer back into the lathe using a back stop, I simply put a parallel behind while the chuck was pinched up the removed the parallel, faced some off took it out of chuck measured it up put it back in chuck up against the parallel, removed the parallel and took a little bit more off to give desired size.

I thinned down a couple of M12 nuts to give me some lock nuts



Now for the pulley this is made out of a bit of 2 " Ally  simple turning job



To cut the Key way in the pulley I made a small 3mm wide shaping tool that was held side ways on in one of my boring bars, to get the tool on centre I measured the centre hight off my lathe setting tool added 1.5mm to this height and that became the height to set the tool.



Setting the tool on height



It was then a mater of winding the saddle back and two and nibble out the key way






Thats all the bits nearly made I can't finish it off until I settle on the motor and grinding wheel fixing which I'll post as part of my Tool Post Grinder build.

These are all the bits



And the assy



Have fun

Stew



A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline Darren

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 3795
  • N/Wales
Re: Making a Sub Spindle
« Reply #40 on: September 22, 2009, 11:37:34 AM »
That's looking really good Stew....really good....nice keyways too.... :clap:
You will find it a distinct help… if you know and look as if you know what you are doing. (IRS training manual)

Offline NickG

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1890
Re: Making a Sub Spindle
« Reply #41 on: September 22, 2009, 12:27:23 PM »
Great stuff Stew well done  :bow:
Location: County Durham (North East England)

bogstandard

  • Guest
Re: Making a Sub Spindle
« Reply #42 on: September 22, 2009, 02:29:02 PM »
Lookin' good Stew.

What you need now is to bring the motor over so we can find out what speed it is running at, then you can calculate out the internal and external grinding pulley sizes.

Please call first.

John

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #43 on: September 22, 2009, 02:38:12 PM »
Thanks John  :thumbup:

Got the sewing machine motor but Dave (bluechip) has a motor that I think will do a better job, I'll be nipping over to his place next week to pick it up. I'll let you know when etc later in the week.

I'm thinking of making a spindle to go with the sewing machine motor for Dremel tooling.

Cheers

Stew



A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline arnoldb

  • Hero Member
  • *****
  • Posts: 515
  • Country: na
  • Windhoek, Namibia
Re: Making a Sub Spindle
« Reply #44 on: September 22, 2009, 03:47:46 PM »
Very nice tutorial Stew  :thumbup: - Thank You ! :clap: :clap:
:beer:, Arnold

Offline CrewCab

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 851
Re: Making a Sub Spindle
« Reply #45 on: September 22, 2009, 03:52:17 PM »
Good thread Stew, thanks  :thumbup:

CC

Offline Maninshed

  • Jr. Member
  • **
  • Posts: 16
Re: Making a Sub Spindle
« Reply #46 on: September 22, 2009, 03:55:59 PM »
Crackin job, you make it look so easy, as everyone seems to say on this site a picture is worth a thousand words. :bow:

Offline dsquire

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2275
  • Country: ca
  • Kitchener, Ontario, Canada
Re: Making a Sub Spindle
« Reply #47 on: September 22, 2009, 04:16:56 PM »
Great job on that spindle Stew. Your makin it look so easy. Thanks for showing it.  :ddb: :ddb:

Cheers  :beer:

Don

Good, better, best.
Never let it rest,
'til your good is better,
and your better best

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Making a Sub Spindle
« Reply #48 on: September 22, 2009, 04:46:02 PM »
Thanks Chaps

 :beer:

Have fun

Stew
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline raynerd

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2893
  • Country: gb
    • Raynerds Projects - Raynerd.co.uk
Re: Making a Sub Spindle
« Reply #49 on: September 24, 2009, 07:23:16 AM »
Looking good :clap:

look forward to seeing it in action as a tool post grinder!

Chris

Offline Gerhard Olivier

  • Sr. Member
  • ****
  • Posts: 314
Re: Making a Sub Spindle
« Reply #50 on: September 24, 2009, 10:14:29 AM »
That is looking very good

Cant wait to see motor, mount atc.

Gerhard
Guernsey
Channel Islands