Author Topic: Evening chaps  (Read 20631 times)

RobWilson

  • Guest
Evening chaps
« on: February 06, 2015, 05:29:27 PM »
Hi Chaps  :wave:

Looks like you lot have been busy wile I have been away  :thumbup: 170 pages of unread post  :palm:


Rob

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8966
  • Country: gb
  • East Sussex, UK
Re: Evening chaps
« Reply #1 on: February 06, 2015, 05:48:21 PM »
Good to see you back Rob.

Did you get remission for good conduct?  :lol:
Andrew Mawson
East Sussex

Offline Bluechip

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1513
  • Country: england
  • Derbyshire UK
Re: Evening chaps
« Reply #2 on: February 06, 2015, 05:52:31 PM »
Hi Chaps  :wave:

Looks like you lot have been busy wile I have been away  :thumbup: 170 pages of unread post  :palm:


Rob


Nurse !!....   Nurse!!!! ......   NURSE!!!!!! ........

He's got loose !!!!!!!!!!!!!!!!!!!!!!!!!!!  :lol:  :lol:  :lol:
I have a few modest talents. Knowing what I'm doing isn't one of them.

Offline vtsteam

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 6466
  • Country: us
  • Republic of Vermont
Re: Evening chaps
« Reply #3 on: February 06, 2015, 06:00:01 PM »
You've got exactly 7 days to make an engine out of old pipe, pipe fittings, nails and a bolt  :poke:  :poke:  :lol:


 :wave: :wave: :wave: :wave: :wave: :wave: :wave: :wave: :wave:

 
I love it when a Plan B comes together!
Steve
https://www.youtube.com/watch?v=4sDubB0-REg

Offline Joe d

  • Sr. Member
  • ****
  • Posts: 251
  • Country: ca
Re: Evening chaps
« Reply #4 on: February 06, 2015, 06:39:26 PM »
Hey there Rob, welcome back.

With all that time you didn't spend on the web, you must have finished that
traction engine? :)

Cheers, Joe

Offline Will_D

  • Hero Member
  • *****
  • Posts: 668
  • Country: ie
    • National Homebrew Club of Ireland
Re: Evening chaps
« Reply #5 on: February 06, 2015, 06:41:44 PM »
Welcome back Rob

reminds me of a "Carry On" sketch:

Nurse !!....   Nurse!!!! ......   NURSE!!!!!! ........

I told you to Prick his Boil !!!!!!!!!!!!!!!!!!!!!!!!!!!  :lol:  :lol:  :lol:
Engineer and Chemist to the NHC.ie
http://www.nationalhomebrewclub.ie/forum/

Offline Bluechip

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1513
  • Country: england
  • Derbyshire UK
Re: Evening chaps
« Reply #6 on: February 06, 2015, 06:51:58 PM »
Yup, I remember that one 'cos we had an actual 'Nurse Duncan' that went in the pub. Someone got the card from Yarmouth IIRC and I got it enlarged and stuck in in the bar ...then ran. She was a hefty girl ...  :lol:

This one ....

http://www.bing.com/images/search?q=no%20no%20nurse%20duncan&FORM=BILH1#view=detail&id=404E306706009CE366480DBC4CE95A4E2B77781F&selectedIndex=0

Dave
I have a few modest talents. Knowing what I'm doing isn't one of them.

Offline dsquire

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2275
  • Country: ca
  • Kitchener, Ontario, Canada
Re: Evening chaps
« Reply #7 on: February 06, 2015, 07:06:03 PM »
They said have patience,  :coffee:  he will return. I did, and he has returned.   :ddb: :ddb:

Glad to have you back Rob.  :D :D

You know the routine, hope you have been taking good care of your camera.  :lol: :lol:

Cheers  :beer:

Don

Good, better, best.
Never let it rest,
'til your good is better,
and your better best

Offline Brass_Machine

  • Administrator
  • Hero Member
  • *****
  • Posts: 5504
  • Country: us
Re: Evening chaps
« Reply #8 on: February 06, 2015, 08:09:50 PM »
Hiya Rob  :wave:

Welcome back to the collective :borg:

Glad to see you back!  :beer:

Eric
Science is fun.

We're all mad here. I'm mad. You're mad.

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #9 on: February 07, 2015, 02:41:00 AM »
Welcome back Rob.

How's the CNC conversion going?

Phil
Phil Fern
Location: Marple, Cheshire

RobWilson

  • Guest
Re: Evening chaps
« Reply #10 on: February 07, 2015, 04:17:20 AM »
Good to see you back Rob.

Did you get remission for good conduct?  :lol:

 :lol: :lol: I did Andrew , I was on the same ward as Dave BC  :hammer:

Hi Chaps  :wave:

Looks like you lot have been busy wile I have been away  :thumbup: 170 pages of unread post  :palm:


Rob


Nurse !!....   Nurse!!!! ......   NURSE!!!!!! ........

He's got loose !!!!!!!!!!!!!!!!!!!!!!!!!!!  :lol:  :lol:  :lol:


 :lol: :lol: :lol: :lol: :lol:,,, hows my capacitor calculations doing  ! :poke:  or do I go for the Geordie method  :zap:   :)


You've got exactly 7 days to make an engine out of old pipe, pipe fittings, nails and a bolt  :poke:  :poke:  :lol:


 :wave: :wave: :wave: :wave: :wave: :wave: :wave: :wave: :wave:

 

Hi Steve , now thats a challenge  :bugeye:  are you building one ?


Hey there Rob, welcome back.

With all that time you didn't spend on the web, you must have finished that
traction engine? :)

Cheers, Joe


Hi there Joe   , in a word  NOPE ! ,,,,,, arrh  but you MUST have your Minie finished by now   :poke: :)   , hows it doing ?



Welcome back Rob

reminds me of a "Carry On" sketch:

Nurse !!....   Nurse!!!! ......   NURSE!!!!!! ........

I told you to Prick his Boil !!!!!!!!!!!!!!!!!!!!!!!!!!!  :lol:  :lol:  :lol:



Thanks Will  :thumbup:  ,, please dont encourage Mr BC   :lol: :lol: :lol:


They said have patience,  :coffee:  he will return. I did, and he has returned.   :ddb: :ddb:

Glad to have you back Rob.  :D :D

You know the routine, hope you have been taking good care of your camera.  :lol: :lol:

Cheers  :beer:

Don




Thanks Don   :beer:  , I haven't looked after the camera so much, just improved my photoshop skills   :)



Hiya Rob  :wave:

Welcome back to the collective :borg:

Glad to see you back!  :beer:

Eric

Good to be back Eric  :thumbup: , there is lots to catch up with  :proj:


Welcome back Rob.

How's the CNC conversion going?

Phil


Cheers Phil ,,,,,,,,,,,, ist NOT  :Doh:   I have been remodelling the shop  ,since you got that CNC lathe from mine I have been given one of those tool grinders I was after (it was been thrown out at my mate place of work ) and I came across a  Colchester Student lathe  also being scrapped due to broken feed gears , I being me I got distracted with other projects  :palm:

Hows the Lathe coming along ?   up and running ? 



Cheers Lads  :beer:

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #11 on: February 07, 2015, 04:39:47 AM »

Hows the Lathe coming along ?   up and running ? 


Rob,

I've made as much progress with the lathe as you have with the mill by the sounds of it. I ripped out most of the control and have bought some microstepping drivers, a breakout board and another 80mm 3-jaw (with both sets of jaws) for it but it's still where I put it in the garage the day I brought it home.

I too am too easily distracted and spend too much time looking after our hydro-electric scheme rather than getting on with jobs at home.

Surely there's no more space in your workshop for a Colchester Student - did something have to go?

 :beer:

Phil.



Phil Fern
Location: Marple, Cheshire

RobWilson

  • Guest
Re: Evening chaps
« Reply #12 on: February 07, 2015, 04:53:45 AM »
Hi Phil


 :lol: :lol: , I thought as much , I am sure both CNC machines will run G code some day  :palm:  , I forgot about you Hydro project ,good to here its still going  :thumbup:

The Student lathe is still sitting at work , well I have some of it at home , TTA,4 jaw ,face plate , tail stock , parts that could be  easily remove . Looks like the Boxfrod lathe will be going the journey to make room  :(  , I am also re doing the welding/casting shop  :loco: , one day I maybe sorted lol


Rob

PS any good engineering reads ? 

Offline John Stevenson

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 1643
  • Nottingham, England.
Re: Evening chaps
« Reply #13 on: February 07, 2015, 05:51:45 AM »
At last....................... :poke:

The return of a worthy adversary   :lol:   :lol: .

Welcome back Rob.
John Stevenson

RobWilson

  • Guest
Re: Evening chaps
« Reply #14 on: February 07, 2015, 09:25:55 AM »
Cheers John  :beer:



The return of a worthy adversary   :lol:   :lol: .



Dominos at fifteen paces  :poke:


Rob

Offline Pete W.

  • Hero Member
  • *****
  • Posts: 852
  • Country: gb
Re: Evening chaps
« Reply #15 on: February 07, 2015, 09:41:35 AM »
Hi there, Rob,

Welcome back.  How are you?


SNIP

I too am too easily distracted and spend too much time looking after our hydro-electric scheme rather than getting on with jobs at home.

SNIP

Phil.

Phil, that sounds interesting, have you posted anything on it?  If not, please do!   :worthless: 
Best regards,

Pete W.

If you can keep your head when all about you are losing theirs, you haven't seen the latest design change-note!

Offline Pete.

  • Hero Member
  • *****
  • Posts: 1075
  • Country: gb
Re: Evening chaps
« Reply #16 on: February 07, 2015, 12:15:12 PM »
Welcome back Rob. Where you been this past year?

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #17 on: February 07, 2015, 12:35:13 PM »
Quote

I too am too easily distracted and spend too much time looking after our hydro-electric scheme rather than getting on with jobs at home.

Phil.

Phil, that sounds interesting, have you posted anything on it?  If not, please do!

Pete,

I've mentioned our hydro scheme once but have never posted photos or any great detail. For starters have a look at our website: http://www.stockport-hydro.co.uk/

Basically we have a twin Archimedes screw system on the River Goyt near Marple in Cheshire. (If I were being pedantic it's actually in Greater Manchester but historically we were in Cheshire.)

The weir was built in the 19th Century for a mill which was never built. There isn't a huge drop on the weir (typically about 1.2m( but it's very wide and so to maximise output we have two screws running side by side. The EA have specified a minimum level of water over the weir of 6cm.  We can take as much water from the river as we like providing we maintain the 6cm level.

The 2 screws can run independently - when the river is very low we run only one screw as it's more efficient.

Unlike most of the early systems ours is a variable speed system meaning that, even when the screws are running very slowly, we can output energy to the grid. The fixed speed systems are often not running in low water conditions because they take too much water to achieve 50hz output to the grid.

Each screw has it's own sluice gate which isn't a control - they're either open or closed.

Each screw is supported at the top by, we believe, a large spherical roller bearing which is capable of taking axial and radial loads. The bottom bearing is a plain bearing which always runs under water. It's fed with biodegradable grease via a pump. The screw is connected to a 90:1 gearbox which in turn drives a three phase permanent magnet motor/generator. (Of the type used as e.g. spindle motors on large machine tools. The motors are rated at 55KW each.)

The motor/generator is driven by an inverter. The inverter is controlled by a Siemens Sinamics module and a PLC. Depending on the river level the inverter drives the motor at a speed (up to a preset maximum) to try to achieve a 6cm weir level. This speed is much slower than the screw would run if it were just allowed to run free with no load. To hold the speed the inverter is constantly braking the screw to slow it to the required speed and it's the braking that generates power. The inverter input is 600v DC and the power generated from the braking is output into the 600v bus.

A third 'grid-facing' inverter is also connected to the 600v dc bus and this inverter converts the 600v dc into 415v three phase 50hz in sync with the grid which we feed into a transformer on a power pole and then into the grid at 11kv.

We can monitor the control and security cctv cameras from home via the web.

In late November we had a major problem with one screw and have not been able to run it. We need to be able to get at the bottom of the screw which is submerged. When the system was built they were running out of money and omitted fitting some steel channels in the tail races where we could fit stop planks which would isolate us from the river and, after pumping out the water, would give us access to the bottom of the screw. It's now going to be more difficult to fit these channels than it would have been when there was a coffer dam in place. I've drawn up the channels and they're now on order. The fitting of them is going to be fun because we'll have to get some fixings in above water level, fit the stop planks, pump out some water to reveal the next set of fixings (which are then only on one side of the channel) etc. etc.

I don't want to go into any detail about how it failed because we are expecting a battle with with the screw manufacturers and the civils contractor on who's responsible for the problem. With a bit of jiggery pokery (wooden props anda sledge hammer) we managed to get the screw running again a few days ago. With the screw not running for 2 months a huge amount of silt had built up which would have hindered the fitting of the channels and stop planks. Running it slowly should clear the silt.

That's all for now - my tea is on the table.

Cheers.

Phil.

Phil Fern
Location: Marple, Cheshire

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8966
  • Country: gb
  • East Sussex, UK
Re: Evening chaps
« Reply #18 on: February 07, 2015, 12:50:12 PM »
Phil that's fascinating - I'd like to read more but the various bits of the web site pointing to FAQ's ,Galley, Progress, Invest, News. History etc don't seem to work :(

Andrew Mawson
East Sussex

Offline vtsteam

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 6466
  • Country: us
  • Republic of Vermont
Re: Evening chaps
« Reply #19 on: February 07, 2015, 12:57:02 PM »


You've got exactly 7 days to make an engine out of old pipe, pipe fittings, nails and a bolt  :poke:  :poke:  :lol:


 :wave: :wave: :wave: :wave: :wave: :wave: :wave: :wave: :wave:

 

Hi Steve , now thats a challenge  :bugeye:  are you building one ?



Almost done, Rob, and RussellT finished his innovative oscillator, Dwayne is the dark horse, still, I suspect some secret developments, there...:

http://madmodder.net/index.php/topic,10261.0.html
I love it when a Plan B comes together!
Steve
https://www.youtube.com/watch?v=4sDubB0-REg

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #20 on: February 07, 2015, 12:59:25 PM »
Phil that's fascinating - I'd like to read more but the various bits of the web site pointing to FAQ's ,Galley, Progress, Invest, News. History etc don't seem to work :(

Andrew,

What browser are you using? I only use Chrome now and all the features of the website seem to work OK. If there is a general problem I'll let the guy who looks after the website know.

Phil.
Phil Fern
Location: Marple, Cheshire

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8966
  • Country: gb
  • East Sussex, UK
Re: Evening chaps
« Reply #21 on: February 07, 2015, 01:20:23 PM »
Google Chrome
Andrew Mawson
East Sussex

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #22 on: February 07, 2015, 01:37:07 PM »
Google Chrome

Strange - I've tested it using Chrome and IE on my laptop and Safari (on my wife's iPad) and Chrome on my Android tablet - all OK!

Phil.
Phil Fern
Location: Marple, Cheshire

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8966
  • Country: gb
  • East Sussex, UK
Re: Evening chaps
« Reply #23 on: February 07, 2015, 02:19:34 PM »
I've marked up the bits that aren't active Phil
Andrew Mawson
East Sussex

Offline DMIOM

  • Hero Member
  • *****
  • Posts: 676
  • Country: gb
  • Isle of Man
Re: Evening chaps
« Reply #24 on: February 07, 2015, 02:34:28 PM »
Andrew,

I suspect it maybe something locked on your browser.

I've just tried Phil's site with Chrome (40.0.2214.111m on W7 / 40.0.2214.109 on Android) and IE 11.0.9600.17501 update 11.0.15 on W7, and all perfectly OK for me.

Dave

RobWilson

  • Guest
Re: Evening chaps
« Reply #25 on: February 07, 2015, 02:51:14 PM »
Site works fine for me Andrew   , Chrome ,windows 7 ultimate  :scratch:

Hi there, Rob,

Welcome back.  How are you?



Thanks Pete , doing fine  :thumbup: yourself , I hope fit and well 

Welcome back Rob. Where you been this past year?


Thank Pete , just been messing around this past year , just plonking about  :loco:



Cheers Rob

Offline awemawson

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 8966
  • Country: gb
  • East Sussex, UK
Re: Evening chaps
« Reply #26 on: February 07, 2015, 03:01:12 PM »
... mmm strange - yes I'm on an oldish laptop running Vista, but using IE 9 (latest for Vista I believe) it works fine  :scratch:
Andrew Mawson
East Sussex

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #27 on: February 07, 2015, 03:14:02 PM »
Rob,

Have you melted any iron yet or is this part of your welding and melting shop reorganisation?

Phil.
Phil Fern
Location: Marple, Cheshire

Offline dsquire

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2275
  • Country: ca
  • Kitchener, Ontario, Canada
Re: Evening chaps
« Reply #28 on: February 07, 2015, 03:19:13 PM »
Andrew

It all works for me and while I was off reading it 3 more replies were made.  :D :D

Cheers  :beer:

Don

I'm using XP3 and Explorer 8
Good, better, best.
Never let it rest,
'til your good is better,
and your better best

Offline krv3000

  • Hero Member
  • *****
  • Posts: 2183
  • Country: gb
Re: Evening chaps
« Reply #29 on: February 07, 2015, 04:23:19 PM »
hi rob brill to see you

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: Evening chaps
« Reply #30 on: February 07, 2015, 04:25:08 PM »
Hi Rob!  :wave:

It's good to see you back with us, again.  :thumbup:

I've been thinking of you, recently. Down a bit, from here...... http://madmodder.net/index.php/topic,10164.msg118117.html#msg118117

Looking forward to you, resuming normal service.  :D

David D
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!

RobWilson

  • Guest
Re: Evening chaps
« Reply #31 on: February 08, 2015, 04:48:12 AM »
Rob,

Have you melted any iron yet or is this part of your welding and melting shop reorganisation?

Phil.

Hi Phil

The welding shop  :(



As you can see it became a dumping ground ,  :palm:    so I decided to move all foundry gear to one side , the moulding bench took a wee bit of moving  :palm:




Then I decided to build a coke forge  :lol: :lol:



Then I threat myself to  some new welders  :)




So I have to fined a home for those now . So the welding shop is still in a state of flux , the cupola just needs a gate valve and blast pipe making , I have 1/2 ton of coke sitting waiting , just need fair weather and a day off .


Rob



RobWilson

  • Guest
Re: Evening chaps
« Reply #32 on: February 08, 2015, 04:54:55 AM »
hi rob brill to see you


Cheers Bob  :)


Hi Rob!  :wave:

It's good to see you back with us, again.  :thumbup:

I've been thinking of you, recently. Down a bit, from here...... http://madmodder.net/index.php/topic,10164.msg118117.html#msg118117

Looking forward to you, resuming normal service.  :D

David D


Cheers David , its good to be back  :thumbup: , nice flywheels  :lol:




Rob

Offline philf

  • Hero Member
  • *****
  • Posts: 1107
  • Country: gb
Re: Evening chaps
« Reply #33 on: February 08, 2015, 04:16:34 PM »
Hi Rob,

You don't do things by halves do you?

 :bugeye:

2 new welders and a plasma cutter and a coke forge!

 :beer:

Phil.
Phil Fern
Location: Marple, Cheshire

Offline Joe d

  • Sr. Member
  • ****
  • Posts: 251
  • Country: ca
Re: Evening chaps
« Reply #34 on: February 08, 2015, 05:53:34 PM »

Hey there Rob, welcome back.

With all that time you didn't spend on the web, you must have finished that
traction engine? :)

Cheers, Joe




Hi there Joe   , in a word  NOPE ! ,,,,,, arrh  but you MUST have your Minie finished by now   :poke: :)   , hows it doing ?




Oddly enough, just started back in on it this week.  Still got lots to go though...

Joe

Offline spuddevans

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1618
  • Country: 00
  • Portadown, Northern Ireland
    • My Photo website
Re: Evening chaps
« Reply #35 on: February 09, 2015, 06:59:57 AM »
Hi Rob  :wave: :wave: Great to see you back, and I can't wait to see what you make with all those lovely new toys  :ddb: :ddb:


Tim
Measure with a micrometer, mark with chalk, cut with an axe  -  MI0TME

RobWilson

  • Guest
Re: Evening chaps
« Reply #36 on: February 09, 2015, 01:00:18 PM »
Hi Rob,
:

2 new welders and a plasma cutter and a coke forge!

 :beer:

Phil.

Hi Phil   , yer ist got me dreaming of a CNC plasma cutter  :zap: ,,,,,,,,,,,,,aarh so many projects  :med:




Oddly enough, just started back in on it this week.  Still got lots to go though...

Joe

Hi Joe

Good to here your still cracking on with her , :thumbup:



Hi Rob  :wave: :wave: Great to see you back, and I can't wait to see what you make with all those lovely new toys  :ddb: :ddb:


Tim


Thanks Tim , I will have to see what I can knock up  :dremel:  just waiting for things to warm up  :coffee: , How is your workshop doing , must be well up and running now ?  last I
                     remember you were fitting new benches  and cupboards .



Cheers Rob 

Offline spuddevans

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1618
  • Country: 00
  • Portadown, Northern Ireland
    • My Photo website
Re: Evening chaps
« Reply #37 on: February 09, 2015, 01:48:07 PM »
How is your workshop doing , must be well up and running now ?  last I remember you were fitting new benches  and cupboards .

Yea, the workshop is as complete as it will be (actually thinking about extending it out the back a little, not for workshop space, just for a covered section for storage of essential junk) I've not been doing much the last couple of months, been a bit cold and been busy with other projects. Hope to be getting back into it soon.

Tim
Measure with a micrometer, mark with chalk, cut with an axe  -  MI0TME

RobWilson

  • Guest
Re: Evening chaps
« Reply #38 on: February 09, 2015, 02:09:35 PM »
Good to here Tim , I no the feeling of being short on space  :palm: , looking to make a small lean to  for storage too ,some were for the growing collection of gas cylinders and the likes .

Just thought ,I have been building my  workshop since I was 13   (when I got my very own shed) and I am still prating about at age 47 , you'd think I would have  it sorted by now LOL   

Aaarh those were the days , two bikes and a bag of tools from Woolworth s , rubber spanners and screwdrivers with see-through yellow handles that explode as soon as you looked at them , happy days .

Rob

Offline raynerd

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2893
  • Country: gb
    • Raynerds Projects - Raynerd.co.uk
Re: Evening chaps
« Reply #39 on: February 25, 2015, 05:51:53 PM »
Hi Rob, hope you are well. Not been on here in a while myself but good to see you are back! How is the shaper?

RobWilson

  • Guest
Re: Evening chaps
« Reply #40 on: February 26, 2015, 11:43:43 AM »
Hi There Chris  :wave:


Yer keeping well and so is the shaper  :dremel: , hows you ,getting any shop time ?


Rob

Offline raynerd

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 2893
  • Country: gb
    • Raynerds Projects - Raynerd.co.uk
Re: Evening chaps
« Reply #41 on: February 26, 2015, 04:30:02 PM »
Not much, few hours a week. Moved house last September and still sorting the workshop out really! New job as well which takes up half my time and my 6yo and 2yo the other half!!