Author Topic: making a new base for a shop lamp ...  (Read 4562 times)

Offline wquiles

  • Jr. Member
  • **
  • Posts: 39
  • Country: 00
    • Work and projects ...
making a new base for a shop lamp ...
« on: December 30, 2009, 08:02:25 PM »
Good lighting helps with the pictures that I take, and I typically use two lamps, one on each side.  About a week ago the weak plastic base of one of them (of course, the cheaper one!) broke off:



I decided to make something a "little" bit stronger by using a small rectangular piece of 6061.  It was also an excuse to try out the higher HP motor on my VFD conversion.  I started taking a 0.5" wide cut, and taking 0.030" and larger chunks to see how well it worked.  Here I am cutting with a two-insert 1" dia cutter:



You can see the progressively larger cuts on the first side (top to bottom, all of them at 0.5"):

 

but on the other side I got more aggressive and cut the 1" inch cut on 3 passes: 0.3", 0.3", and 0.4" (again, all of them at 0.5"):

 

I then finished cleaning up the edges a little (no effort was made to  make the part look pretty):

 

then drill all 5 holes:

 

 

The finished piece next to the broken one:

 

 

and in use, with the original cheap lamp:

 

and with the heavier, much nicer lamp:

 

Will
Machining and electronics - www.atdms.com

Offline chuck foster

  • Sr. Member
  • ****
  • Posts: 334
  • Country: ca
Re: making a new base for a shop lamp ...
« Reply #1 on: December 30, 2009, 08:11:54 PM »
nice job will  :thumbup:

i had the same problem with one of the lights in my shop..........so i did the same as you.

chuck  :wave:
hitting and missing all the way :)

skype:  aermotor8

former hmem member

Offline Divided he ad

  • WARNING: LIKES SHINEY THINGS
  • The Collective
  • Hero Member
  • *****
  • Posts: 1950
  • Country: gb
  • Between Chester, Wrexham, ruthin & Holywell :-)
Re: making a new base for a shop lamp ...
« Reply #2 on: December 30, 2009, 08:41:51 PM »
Nice job there Will..... Makes me feel all lazy!!

I just drilled a hole through my bench for mine! ::)





Ralph.
I know what I know and need to know more!!!

Offline Powder Keg

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 932
  • Country: us
  • Machinist Extraordinaire
Re: making a new base for a shop lamp ...
« Reply #3 on: December 30, 2009, 09:47:51 PM »
Nice job!!! I buy those at thrift stores and they are always missing the base. You can pick them up for a couple of bucks usually. Here is a base I make. It's wood that's glued and screwed together. Then a coat of paint and your set:o)

Wesley P
A Gismo ??? If it has a flywheel or spins and is made with small parts. I'll take one! If it makes noise, moves, or requires frequent oiling and dusting it's a better deal yet. It's especially right if its shiny and bright; but if it's dirty and dull it wont mater at all...

Offline wquiles

  • Jr. Member
  • **
  • Posts: 39
  • Country: 00
    • Work and projects ...
Re: making a new base for a shop lamp ...
« Reply #4 on: December 30, 2009, 11:17:53 PM »
Thank you guys.  I am also happy to see that I am not the only one using these lamps.  It is cool to hear and see how you guys have dealt with the poor/fragile bases - there are many ways to skin this cat  :D
Machining and electronics - www.atdms.com