« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: Mill Tapers?  (Read 18858 times)

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: Mill Tapers?
« Reply #25 on: April 06, 2011, 02:14:23 AM »
Yesterday, I made my first chippings......  :D

I squared across the end of a piece of steel, using the full length of an 18mm endmill..... What a revelation!  :bugeye:

Sweet, smooth, quiet......  With the cutter directly in the snout, rather than ER32 holder, the head is much lower and more rigid.  :thumbup:

Very pleased with my new "GT" mini mill...... Thank you all, for your input.  :clap: :clap:

David D
Logged
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!

Offline sbwhart

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3530
  • Country: gb
  • Smile, Be Happy, Have Fun and Rock Until you Drop
Re: Mill Tapers?
« Reply #26 on: April 06, 2011, 02:21:13 AM »
Hi Dave

Good to see your back in the chip making buisness  :thumbup:


When are you going to start killing that Robinson engine  :poke:
 
 :D

Stew
« Last Edit: April 06, 2011, 02:23:12 AM by sbwhart »
Logged
A little bit of clearance never got in the road
 :wave:

Location:- Crewe Cheshire

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: Mill Tapers?
« Reply #27 on: April 06, 2011, 04:20:24 AM »
Kenneth.
Thanks for that! I'll post a project build, in a day or so.....  :thumbup:


Stew.
I've got to catch up with a few bits an bobs.... Then, the Mrs Robinson saga will be re started......  :wave:

Hmmmm...... That means I've got to show "that pic"..... Doesn't it!  :bang: ...... And what's happened since.....  :bang:  :bang:

Hmmmm.......  ::)

David D

Logged
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: Mill Tapers?
« Reply #28 on: April 08, 2011, 12:26:43 PM »
Quote from: Da_Kengineer_Meister on April 06, 2011, 02:19:14 AM
Great News David!   :thumbup:  Do you have a re-assembled w/tool mounted photo to go with it?  -Congratulations!

Hi Kenneth.
Is this what you mean?

6mm cutter, in R8 collet......




Head well down the slideway. More rigid than (previously) using an ER32 holder.......




Working on the write up, at the mo.....

David D
Logged
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!

Offline Stilldrillin

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4972
  • Country: gb
  • Staveley, Derbyshire. England.
Re: Mill Tapers?
« Reply #29 on: April 08, 2011, 03:37:03 PM »
Quote from: Da_Kengineer_Meister on April 08, 2011, 12:36:03 PM

If you added all the working / planning / parts ordering time together how much time do you think you have invested?

That's not a fair question, Kenneth!  :bugeye:

Lets just say. Far too much, as far as Mrs Drillin is concerned!  :thumbup:

David D
Logged
David.

Still drilling holes... Sometimes, in the right place!

Still modifying bits of metal... Occasionally, making an improvement!
Pages: 1 [2]  All   Go Up
« previous next »