Author Topic: New MIG Welder  (Read 7809 times)

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
New MIG Welder
« on: January 15, 2014, 07:11:13 PM »

     


John
« Last Edit: January 15, 2014, 09:26:21 PM by dsquire »

Offline dawesy

  • Sr. Member
  • ****
  • Posts: 252
  • Country: gb
Re: New MIG Welder
« Reply #1 on: January 16, 2014, 04:28:59 AM »
Looks like a nice substantial unit there john. Wire feed looks decent too, usually the biggest problem with the smaller hobby units.
Looking forward to seeing it in use.
Lee.
wishing my workshop was larger :(

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: New MIG Welder
« Reply #2 on: January 16, 2014, 02:01:37 PM »

     


« Last Edit: January 16, 2014, 03:54:43 PM by dsquire »

Offline Pete W.

  • Hero Member
  • *****
  • Posts: 852
  • Country: gb
Re: New MIG Welder
« Reply #3 on: January 16, 2014, 02:44:18 PM »
Hi there, John,

I can't read Reply #2 - is it that misplaced square bracket again? 
Best regards,

Pete W.

If you can keep your head when all about you are losing theirs, you haven't seen the latest design change-note!

Offline dawesy

  • Sr. Member
  • ****
  • Posts: 252
  • Country: gb
Re: New MIG Welder
« Reply #4 on: January 16, 2014, 03:15:52 PM »
Very nice john. Been there and dropped a spool before and had the end slip out my fingers. Your right 'bŁ&@cks is the right word :)
Lee.
wishing my workshop was larger :(

Offline krv3000

  • Hero Member
  • *****
  • Posts: 2183
  • Country: gb
Re: New MIG Welder
« Reply #5 on: January 19, 2014, 01:49:46 PM »
well dun john do you want a flow meter for it

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: New MIG Welder
« Reply #6 on: January 19, 2014, 01:54:21 PM »
Hi
Bob
Just put the flow meter on that you gave me  :D :D
John

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: New MIG Welder
« Reply #7 on: January 25, 2014, 06:36:06 PM »


« Last Edit: January 25, 2014, 07:52:38 PM by dsquire »

Offline S. Heslop

  • Hero Member
  • *****
  • Posts: 1154
  • Country: gb
  • Newcastle Upon Tyne
Re: New MIG Welder
« Reply #8 on: January 26, 2014, 12:18:28 PM »
Got a good laugh at the end of this one.

Offline John Rudd

  • Hero Member
  • *****
  • Posts: 2521
  • Country: gb
Re: New MIG Welder
« Reply #9 on: January 26, 2014, 01:52:11 PM »
John just never ceases to amaze me..... :

But his sense of humour is just inimitable   :lol:
eccentric millionaire financed by 'er indoors
Location:  Backworth Newcastle

Skype: chippiejnr

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: New MIG Welder
« Reply #10 on: February 03, 2014, 04:45:17 PM »

Offline krv3000

  • Hero Member
  • *****
  • Posts: 2183
  • Country: gb
Re: New MIG Welder
« Reply #11 on: February 03, 2014, 05:10:24 PM »
well dun you will be making a bote for that engine to go in next

Offline micktoon

  • Hero Member
  • *****
  • Posts: 797
  • Country: gb
Re: New MIG Welder
« Reply #12 on: February 03, 2014, 06:05:47 PM »
Hi John , I cant wait to see this baby get cranked right up  :ddb: its getting nice welds in that latest vid on the half setting I bet it will melt in lovely on full power  :drool:, my 165 amp Murex is not as good at thicker stuff as this welder was on this vid. I cant complain as its been faultless for a good 20 odd years and just does the job with no hitches in general.
  Cheers Mick.

Offline doubleboost

  • Madmodder Committee
  • Hero Member
  • *****
  • Posts: 1619
  • Country: gb
  • Newcastle Upon Tyne
Re: New MIG Welder
« Reply #13 on: February 11, 2014, 05:31:37 PM »